Corduroy Shirt Dress

To make this dress, I started with a men's XXL corduroy shirt, and and men's L sweater.

Cut away the shirt collar, leaving the neck band.

Use part of the collar to create an extension for the future sweater collar.  The buttonhole on the collar tip will come in handy.  Be careful not to stitch over the existing buttonholes, you will use them.

Cut away the sleeves.

Carefully pick out the side seam stitching of the sweater (which should give you edges that don't unravel.)  Cut 5 1/2" off the bottom edge of the sweater front.  This will give you a collar piece that is finished on three sides.  Serge the unfinished cut edge. 

Pin the right side of the collar to the wrong side of the collar band and extension, easing if necessary.  Stitch in place.

Button up the collar band and mark where the button should be placed for the collar extension.  Since the fabric is kind of thick, sewing the button over a pin, and then removing the pin, will make it easier to button through the thickness.

Fit the shirt to your size and take in the side seams.  Cut your new sleeves from the bottom of the original sleeves, retaining the cuff detail.  I opted for a straight edge, dropped sleeve so that I didn't have to mess with cutting the upper curve to a new sleeve.  Stitch the sleeve in place.

Cut about 9" from the bottom of the sweater sleeves and take in seams as needed to fit.  Serge the unfinished edge.  Place the sweater sleeve into the dress sleeve, matching side seams.  Pin and stitch in place.  I left the shirt cuff unbuttoned to give me more ease in wearing.  You may have to hand stitch the sweater sleeve in place.

Square off the front and back tail of the shirt.  Retain these scrap pieces incase a waist inset is needed for added length.

  

Open the side seams of the leftover upper sleeve pieces.  You can do this by unpicking the stitching, or in my case, they were flat felled seams and I just cut close to the edge.  Overlap the sleeves and stitch in place.  Since I cut close to the flat felled seam, I didn't have to finish the slit edge.  If you have a raw edge, finish it before overlapping and stitching.  This will become the back slit of your dress. 

  

Square off the top edge of the upper sleeve pieces, pin and stitch this bottom band to the dress.  (As a side note, I stitched down the back pleat of the shirt before adding the bottom band.  I also duplicated the front plaque detail with buttonholes as you can see from the second picture.)

Front plaque detail of bottom band, with added buttonhole, made to match original plaque detail.

The dress wasn't quite long enough for me, so to get some extra length I added an inset waist piece, turning the front edges to the inside.

  

Stitch elastic to each seam, stretching the elastic as you go.

When complete, the inside should look like this.  Add a button and buttonhole to the waist.  (I had to piece together various scrap pieces to create the waist inset.  But, I didn't worry too much since it would be covered by a belt.)  All that was left was to hem it with a simple rolled hem.

So there you have it, a corduroy shirt dress!  You can view the tutorial of the sweater purse here.

Belted Sweater Purse

I started with a large sweater, corduroy pants, and a large belt.  I also used some iron-on interfacing, and your standard sewing supplies.

I had used part of this sweater already as trim on this dress.  With the remaining sweater, I cut the main portion of my purse.  It measured 16" x 16".  I also cut the same from my iron-on interfacing.  The corduroy lining was also cut 16" wide, but I added an extra 2" to the height to allow for the top edge of the lining to eventually fold over and finish off the top of the purse.

Iron the interfacing to the back of the sweater pieces.  The interfacing will give you stability when sewing the stretchy sweater fabric.  It will also give your purse some needed shape.

With right sides together, stitch across the bottom of the purse.

I pressed the bottom seam open and then stitched it in place to reduce bulk.  You won't see this stitching as it will be covered in the next step.

Cut a piece of corduroy 16" wide by whatever height you want.  I made mine about 7".

Press under both edges of the corduroy fabric, center the fabric on the bottom seam of the purse, pin and stitch in place.

Fold the bag in half, right sides together, and stitch the side seams.  Turn the bag inside out and stitch a boxed corner on each side.  Trim away the excess.  (Trimming not shown.)

If you want a pocket on the inside of your purse, now's the time to attach it.  Once it's sewn in place, stitch the bottom and sides of the lining.  Box the corners like you did with the sweater fabric.

Cut and stitch belt loops.  I made mine long enough to accommodate the belt and then have the excess be stitched into the top binding.  (Refer to the picture of the completed purse at the beginning of this post.)  I left the top edges unfinished since they would eventually get covered by the binding.  The bottom edges were folded under and stitched in place.  I placed two belt loops in the front, and two in the back. 

Slip the lining into the bag and roll the excess fabric over the top to create a binding.  I stitched this in place by hand since it was getting pretty thick.

Cut two straps approximately 3" by whatever length you desire.  Fold in half lengthwise, right sides together and stitch, creating a tube.  Turn them right side out and press.  Topstitch 1/4" along the edges.  Pin in place on the purse and stitch.  Measure the belt to go around the purse, cut off any excess.  Punch new holes for the belt buckle.  Use any leftover belt scraps as embellishments.  I used the pieces to cover the raw edges of the straps where they attached to the purse.  I also had enough to create a flap that keeps the purse closed with a button.  (Refer to the photos of the finished purse.)

Hopefully, this tutorial has been helpful.  The hardest part was probably the thickness of the sweater and corduroy.  Make sure you use a heavy duty needle!